Wind is the peril that puts the most Dallas-Fort Worth roofs back on the replacement list, and roofing is what American Prime General Construction does first and does itself. Wind lifts shingles and breaks the seal strip, creating hidden leaks even when the roof looks fine. We inspect for creased shingles, missing fasteners, exposed underlayment and damaged flashing, then document the findings and outline the repair or replacement path.
We are a veteran-led roofing contractor and general contractor in Richardson, so the company that diagnoses the roof also performs the roof repair or roof replacement, restores the exterior, and handles any interior build-back. Below is how wind defeats a shingle roof and what code and test standards require.
Schedule a Free Roof Inspection Call 469-888-8326
How Wind Uplift Fails an Asphalt Shingle Roof
Wind does not simply push on a roof. Air separating over the ridge, hips and edges creates suction that pulls upward on the exposed edge of each shingle course. A shingle resists that force through two things: the nails holding it to the deck and the sealant strip bonding each course to the one below.
Seal strip failure
The sealant strip goes first and is the hardest failure to see. Once a course unseals it flutters in every later wind event and the nail holes become leak paths. GAF states that if shingles do not seal properly, the wind resistance of the installation is reduced and the shingles are more likely to break off, in Technical Advisory Bulletin TAB-R-115, and notes a lifted shingle will not reseal and must be hand sealed.
Creasing and tab loss
When an unsealed shingle folds back on itself, the asphalt and fiberglass mat crack along the fold. That crease is permanent and granule loss accelerates along it. Creasing is the most common wind finding here and is often invisible from the ground.
Ridge, hip, rake and eave vulnerability
Suction is highest at the perimeter and at changes in plane, so ridge caps, hip caps and rake and eave courses fail first. The code treats the edge as structural: 2021 IRC Section R905.2.8.5 requires drip edge at eaves and rakes, laps of at least 2 inches, extension at least 1/4 inch below the sheathing and 2 inches onto the deck, fastened at not more than 12 inches on center.
What Wind Can Do to a DFW Home
- Creased, lifted or missing shingles and broken sealing strips at ridges, hips, rakes and eaves
- Exposed underlayment and fastener pull-through
- Damaged flashing, ridge caps, pipe boots and accessories
- Siding, gutter, fencing, soffit, fascia and window damage
- Water intrusion and interior damage once the envelope is breached
Damage is rarely confined to one component. A gust strong enough to unseal a slope also loosens gutter hangers and pushes fence sections past plumb, items routinely missed on a roof-only walkthrough.
Shingle Wind Resistance Ratings and the Standards Behind Them
Wind resistance is a test result, not a marketing figure. ASTM D3161 is a fan-induced uplift test producing Class A, D and F; ASTM D7158 produces Class D, G and H. Section R905.2.4.1 of the 2021 IRC requires shingles to be tested to ASTM D7158, to meet Table R905.2.4.1 for the applicable ultimate design wind speed, and to carry labeled packaging.
| Ultimate design wind speed, Vult (mph) | Basic wind speed, VASD (mph) | ASTM D7158 class | ASTM D3161 class |
|---|---|---|---|
| 110 | 85 | D, G or H | A, D or F |
| 116 | 90 | D, G or H | A, D or F |
| 129 | 100 | G or H | A, D or F |
| 142 | 110 | G or H | F |
| 155 | 120 | G or H | F |
| 168 | 130 | H | F |
Values from Table R905.2.4.1 in the 2021 IRC, Chapter 9. Owens Corning publishes wind resistance up to 130 mph for TruDefinition Duration shingles, ASTM D3161 Class F and ASTM D7158 Class H, and requires six nails per shingle for its enhanced wind warranty, per Owens Corning product documentation.
The Design Wind Speed That Applies in Dallas-Fort Worth
The governing number is in Table R301.2 of the adopted residential code, which localizes the map in Figure R301.2(2). The 2021 IRC as adopted by the City of Dallas lists an ultimate design wind speed of 115 mph 3-second gust (76 mph fastest mile), no special wind region, no windborne debris zone, and Plano lists the same 115 mph value. Against the table above, that speed falls where Class D, G or H shingles are acceptable, and Class H is acceptable everywhere. Confirm the criteria your own city has adopted.
Nail Placement and Fastening Requirements
Fastening decides wind performance and is the part of the job nobody sees. Section R905.2.5 requires galvanized steel, stainless steel, aluminum or copper roofing nails, minimum 12-gage (0.105 inch) shank with a minimum 3/8-inch head, complying with ASTM F1667, penetrating not less than 3/4 inch into the sheathing or entirely through thinner sheathing. Section R905.2.6 requires the manufacturer’s minimum count and never fewer than four fasteners per strip shingle.
Placement matters as much as count. GAF specifies fastening 6 inches from the bottom edge on metric shingles and 5-5/8 inches on English shingles, with fasteners hitting the double-thickness nail line, per TAB-R-115; nails above that line can pass through the sealant, which the bulletin says lets it oxidize or become contaminated so the shingles never seal. FEMA recommends shingles rated for 90-plus mph wind with four nails minimum, six preferred, in Tornado Recovery Advisory RA7. IBHS requires 8D ring-shank nails in an enhanced pattern for its FORTIFIED Roof standard and states the change can double the uplift a roof withstands, per IBHS.
Decking, Underlayment and What Gets Exposed
Once shingles leave, underlayment and decking are all that remain, and neither is built for exposure. The 2021 IRC requires shingles to be fastened to solidly sheathed decks and sets underlayment attachment in Section R905.1.1, including a cap-nail grid with shanks reaching at least 3/4 inch into the sheathing where wind design applies, per the 2021 IRC Chapter 9 underlayment tables. IBHS reports that sealing deck seams can reduce water intrusion by up to 95 percent if the covering is lost, per the FORTIFIED Roof program – an inexpensive upgrade while the roof is open, which we review when you plan a roof replacement.
Wind Damage to the Rest of the Exterior Envelope
Fascia, soffit and gutters
Fascia takes uplift on its top edge and gutter load on its face, so it splits at the nail line or pulls apart at the joints. Soffit panels fail when eave suction pulls them from the receiving channel, admitting wind-driven rain into the attic. Gutters loosen at the hangers and lose pitch.
Siding, windows and fencing
Lap siding unlocks at butt joints and the nail hem, composite boards crack, and a loose panel becomes debris for the next gust. FEMA notes windows and doors can be dislodged from walls unless shimmed and nailed into the framed opening with nails long enough to tie into adjacent studs, in Advisory RA7. We handle these repairs with the roof, including siding and window work.
From Inspection to Complete Build-Back
APGC documents the damage, prepares the repair scope, and manages roof repairs, roof replacement, exterior restoration and any required interior build-back. Where drying or specialized mitigation is needed, properly licensed mitigation companies perform it; our role is mitigation and remediation partner coordination, sequencing their work with the reconstruction we self-perform. Projects run from inspection and documentation to a written scope, material selection, permitting, tear-off, installation and a final walkthrough.
For a disputed loss, start with a certified forensic roof inspection; for mixed-peril events see storm restoration and tornado reconstruction.
Documentation, Claims and What We Do Not Do
We assemble dated photographs by elevation and slope, roof measurements, written scopes, material specifications and code references. We are not a public insurance adjuster and we do not negotiate claims on your behalf. The Texas Department of Insurance advises homeowners to photograph the damage, cover openings and save receipts, and notes that waiving a deductible is illegal under state law, in its guidance on what to do after hail or windstorms. See our documentation page.
Frequently Asked Questions
What does wind damage look like on a roof?
Wind lifts shingles and breaks the factory seal strip, creating hidden leak paths even when the roof looks fine from the ground. We inspect for creased shingles, torn tabs, missing fasteners, exposed underlayment, displaced ridge caps and flashing damage. Creasing is permanent damage.
Do you repair more than the roof?
Yes. Wind damage reaches siding, gutters, fencing, windows, soffit, fascia and interior finishes once water enters. APGC self-performs roofing and exterior work and manages the build-back on one schedule.
Do you provide documentation for the insurance claim?
We provide construction estimates, photographs, measurements, repair scopes, material information and code documentation for the required work. We are not a public insurance adjuster and we do not negotiate claims on your behalf.
What areas do you serve?
American Prime General Construction is at 2100 N Greenville Ave Ste 106, Richardson, TX 75082, and serves Dallas, Plano, Garland, Allen, McKinney, Frisco, Rowlett, Carrollton and nearby DFW communities. Call (469) 888-8326.
What design wind speed applies to a roof in the Dallas area?
Table R301.2 of the 2021 International Residential Code as adopted in Dallas lists an ultimate design wind speed of 115 mph as a 3-second gust, with no special wind region and no windborne debris zone. Plano lists the same value. That is a design criterion, not a guarantee for any given roof.
How many nails does a shingle actually need?
Section R905.2.6 of the 2021 IRC requires the manufacturer’s minimum count and never fewer than four per strip shingle. FEMA recommends four nails minimum, six preferred, and Owens Corning requires six per shingle for enhanced wind warranty coverage.
Can wind damage be repaired, or does the whole roof need replacing?
It depends on how widespread the seal failure is and whether existing shingles can be matched. Scattered damage on one slope is often a repair. When creasing and seal loss cross several slopes, replacement is usually sounder. We document both options.
Does a new roof have to meet a specific wind rating?
Section R905.2.4.1 of the 2021 IRC requires shingles to be tested to ASTM D7158 and to meet Table R905.2.4.1 for the applicable ultimate design wind speed. At the speeds mapped for North Texas, Class D, G or H satisfies the table; Class H is acceptable at every listed speed.
American Prime General Construction is a veteran-led roofing contractor and general contractor at 2100 N Greenville Ave Ste 106, Richardson, TX 75082, (469) 888-8326. We handle roofing, hail damage restoration and reconstruction and build-back across the metroplex, including Plano and Dallas. See service areas or contact us.